Home > Western Digital > Western Digital Passport Cable Test Read Diagnostics Sector Error

Western Digital Passport Cable Test Read Diagnostics Sector Error

This may be an anomaly or a defect with the drive. It powers up, the motors gain speed, then I could hear the head trying to read something for a few seconds(10 to 15 seconds to be precise) while the LED is it now detects the physical drives, but gives 11-Cable Test::Write sector error! Replace drive if unable to correct error 120 NO DRIVE FOUND Cannot communicate with drive. check over here

Then the Drive comes quite and LED stays steady.However when I tried to do create a full disk image, it 'clicked' a few times - only once in every 2 minutes The drive has not responded in the time allotted. The Drive spins up and the LED blinks but the partitions do not appear in Windows explorer. I do not have the HDD with me right now.As I mentioned, one of the partitions is Bitlocker encrypted. https://community.wd.com/t/11-cable-test-write-sector-error/13087

Replace Drive 225 Too Many Errors Found Error count reached a threshold value. Replace Drive 161 RESET SIGNATURE The drive did not properly respond to test commands. Re-Test Drive 18 Read Verify Sector Ext Error A Read Verify Sector Ext command during the test has failed. If any of the tests fail, including the Quick Test, replacement of the drive may be necessary.

This may be due to a defect with the drive or a bad connection. The 'Adavcned scan' got stuck at some point and I had to abort it.What do you think happened? Step 4 Download the WD tool Data Lifeguard Diagnostics from here: http://support.wdc.com/product/download.asp?groupid=810&lang=en and test your drive. Test Time: 05:59:17, October 19, 2009 Test Option: EXTENDED TEST Model Number: WDC WD5000BEVT-11ZAT0 Unit Serial Number: WD-WXNX08NC5444 Firmware Number: 01.01A01 Capacity: 500.11 GB SMART Status: FAIL Test Result: ABORT Test

Ten or more instances of information on data positioning and location could not be found. Check Floppy and use appropriate diagnostic utility 207 Critical Resource Error Unable to locate and/or use a system resource (e.g. - printer). Replace Drive 213 2-9 DAM Errors Data Address Mark (DAM) 2-9. The drive may not have been accessed properly possibly due to a bad connection.

failure and errors How to test a drive for problems using Data Lifeguard Diagnostics for Windows Where to download software, utilities, firmware updates, and drivers for WD products Processing... Re-test Drive 134 Busy Timeout Timeout from checking busy bit. Any easy hope here??- Any other backup software could help on this regard?Thanks in Advance. 21 answers Last reply Nov 2, 2014 Best Answer Oct 20, 2014 More about passport external Re-Test Drive 14 Test Suspended A test has been temporarily suspended by the user.

Retest after checking the connections. http://data.lifeguard.diagnostics.cable.test.read.diagnostics.sector.error.winadvice.org/ Re-Test Drive 10 Set File Pointer Error A SetFilePointer command during the test has failed. Check cabling and retest. You may also want to reroute your IDE cable away from sources of electronic bus noise such as your CPU, Power Supply, etc.

Check cable & retest. http://txtbl.com/western-digital/western-digital-diagnostics-error-code-223.html Please rate the helpfulness of this answer Answers others found helpful Understanding S.M.A.R.T. Windows no longer detec « Reply #9 on: June 30, 2013, 02:00:43 PM » The 'SMART information' context menu item is disabled for this particular drive (in iRecover).'WD Drive Utilities' software It also says 'You need to initialize the Disk before you could use it'As far as I know only new harddisks need to be initialised.

Re-Test Drive 104 Drive Not Ready The drive did not properly respond to test commands. If ECC occurs, use Data Lifeguard repair option for additional error correction. Back up as soon as possible before the drive completely fails and the data will become UNRECOVERABLE. this content No, the problem, at least for me, is the drive.   The only reason I had to search out the Data Lifeguard Windows Tool is because I was having issues with my

Return to Top Data Lifeguard Tools 11 and 10 Error Codes Note: If the same error code is encountered more than once after re-testing, please Contact Us for additional assistance. Replace Drive 217 2-9 SERVO Errors SERVO 2-9. Status code = 04 (Unknown failed test element), Failure Checkpoint = 96 (Unknown Test) SMART self-test did not complete on drive 4!

Re-Test Drive 109 DRQ WAS SET The drive did not properly respond to test commands.

If the drive still is not recognized, than it is most likely damaged and needs to be replaced. If ECC occurs, use Data Lifeguard for additional error correction. Between two to nine errors have been detected. Privacy Policy Terms of Use Trademarks Select your Language Language 中文(繁體) 中文(简体) Čeština Deutsch English Español Francais ελληνικά Italiano 日本語 한국어 Polski Português РУССКИЙ Türk Return to WDC.com WD Community Contact

I chose 'Support Analysis Report' option. http://www.myshopping.com.au/ZM--383653838_Hard_Drives If you object to my “Candourâ€, read another post ! "BENE DICTUM, BENEDICTE !" pcbugfixer, #8 2009/10/19 braindead Inactive Thread Starter Joined: 2009/02/09 Messages: 265 Likes Received: 2 Trophy Drive should be replaced. have a peek at these guys For full access please Register.

Windows no longer detec « on: June 22, 2013, 03:48:25 PM » I have a 1TB Western Digital MyPassport USB3.0 external hdd. Start iRecover, get to a screen that has the disks listed and right-click on the disk. The drive has detected an unstable condition, possibly an incorrect spin speed. Return to Top Data Lifeguard Tools 5.22 for DOS Error Codes Note: If the same error code is encountered more than once after re-testing, please Contact Us for additional assistance.