Finally got around to trying to make Windows XP work and now it looks like the HD is bad as well! The HD is a Western Digital 320GB Sata II Edited by guman0v, 14 March 2010 - 06:49 PM. I ran chkdsk /r on the drive and 3/4 of the way through chkdsk it said it replaced bad clusters in file *.* After chkdsk completed I located the file referred Create and use a new DLG Tools diskette. check over here
Check cable and retest. Replace Drive 456 IDNF 1 Identified Data Not Found. The cable is loose, broken, or not plugged in. Re-test and Repair Option diagnostic utility 212 10+ Uncorr ECC Errors Error Correction Code (ECC) 10+.
Join them; it only takes a minute: Sign up Here's how it works: Anybody can ask a question Anybody can answer The best answers are voted up and rise to the Browse other questions tagged hard-drive hardware-failure smart or ask your own question. Test complete Defect Free Now, can I assume that the hard drive is now fine, and more errors won't crop up in the future?
Replace Drive 457 IDNF 2-9 Identified Data Not Found. Replace your cable and retest the drive. Check cabling & retest. Recheck your connections and replace the cable.
The drive is defective. Western Digital Error Code 0007 An onboard defect counter has determined the drive has too many errors and should be replaced. Retest. Several instances of information on data positioning and location could not be found.
Check your floppy and retest. Re-Test Drive 258 ECC 10+ Error Correction Code. This error can occur on non-Western Digital drives. Thanks.
My WebsiteMy help doesn't cost a penny, but if you'd like to consider a donation, click Back to top #14 guman0v guman0v Topic Starter Members 18 posts OFFLINE Local Replace the drive if the error repeats. Western Digital Error Codes Computer Help Aug 26, 2016 Turns on and off repeatedly. Contact System Vendor 221 Test Not Supported Certain older drives do not support certain SMART Self Tests.
Replace. http://txtbl.com/western-digital/western-digital-error-code-0223.html This may be an anomaly or a defect with the drive. Replace Drive 227 SMART Not Supported Self-Monitoring, Analysis, and Reporting Technology (SMART) Certain older drives do not support SMART. The drive has not responded to the SMART test request.
Re-Test Drive 19 SMART Enabled Operation Failure Self-Monitoring, Analysis, and Reporting Technology (SMART) Enable Operation failed. a minute every now and then. Replace drive if unable to correct error 118 DAM Error Data Address Mark (DAM) Error. http://txtbl.com/western-digital/western-digital-hard-drive-error-code-0226.html Replace Drive 217 2-9 SERVO Errors SERVO 2-9.
to report if a drive has failed, it must be enabled as a system option. This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection. Why can't the second fundamental theorem of calculus be proved in just two lines?
Replace the drive if the error repeats. I hope the owner can come up with a copy of Windows XP home. Replace the drive. This is the pretest initialization code which indicates a drive is ready to be tested, but has not yet been tested.
failure and errors Warranty policy and online warranty services for WD products Processing... moon1 2011-03-15 13:38:52 UTC #11 any time;) acrufox 2011-03-21 15:34:54 UTC #12 Interesting. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 46 00 00 00 40 Device Fault; Error: ABRT have a peek at these guys Re-Test Drive 112 IRQ Timeout Interrupt ReQuest Interrupt signal not received.
Replace Drive 212 Error while relocating TARE sectors. Non-WD drives are not supported. Re-test Drive with appropriate diagnostic utility 205 Aborted By User Test was aborted by the user (Alt-X pressed during a test). The results are very strange.
Ensure that you are using the latest version of diagnostic utility and that your cable is in good working condition. An interrupt command to perform a specific task failed to complete. No, create an account now. EDIT: No dice.
It "wraps" after 49.710 days.