Home > Western Digital > Western Digital Error Status Code 0226

Western Digital Error Status Code 0226

The drive spins up and spins down just fine, but it goes into that accessing clicking loop very soon (seconds) after I try to boot from the drive or access files Re-test Drive with appropriate diagnostic utility 205 Aborted By User Test was aborted by the user (Alt-X pressed during a test). can you do a long test? Now, after all the restarts, it doesnt even seem to want to do these things any more. check over here

Getdataback does it again... If you're new to Tech Support Guy, we highly recommend that you visit our Guide for New Members. Replace the drive if the error repeats. The drive may not have been accessed properly possibly due to a bad connection.

The automatic repair feature can attempt a repair if possible. If ECC occurs, use Data Lifeguard repair option for additional error correction. At some point, however, the spare pool is exhausted, and no relocation nor remapping can take place. rosh325, Sep 13, 2007 #7 rosh325 Thread Starter Joined: Jan 30, 2003 Messages: 1,098 Also, why is the HDD activity light coming on right from the start, even though I am

to report if a drive has failed, it must be enabled as a system option. Replace the drive. The only computer users I know are mac users. It then booted up, passed POST, but could not find the Hard drive.

Replace the drive if the error repeats. Replace the drive if the error repeats. The drive has not responded back in the time allotted. http://superuser.com/questions/679260/western-digital-sector-relocation-error-code-226 At least this is a start rosh325, Sep 13, 2007 #9 Blue Zee Joined: May 18, 2007 Messages: 1,759 Windows 98 CDs are not bootable, Win98SE are....

Data request has timed out when writing to the drive. Several instances of information on data positioning and location could not be found. Good to know that it is still a reliable [email protected]: there are two copies of the metadata, stored in roughly the same places as the old fat tables were. Replace Drive 211 2-9 Uncorr ECC Errors Error Correction Code (ECC) 2 through 9.

Download address : http://www.ultimatebootcd.com/download.html Burn the ISO using Imgburn. recommended you read Drive should be replaced. Please ensure that you are using the version of diagnostic utility corresponding to either newer or older Western Digital drives. Drive should be replaced.

Replace Drive 550 Abort Cmd Abort Command. http://txtbl.com/western-digital/western-digital-hard-drive-error-code-0226.html Replace Drive 0009 - 0014 SMART Error Self-Monitoring, Analysis, and Reporting Technology (SMART) Error returned during SMART Status/Self Test Command. Re-test 132 Command Error Command Aborted. If ECC occurs, use Data Lifeguard for additional error correction.

Family and loved ones will always be a priority in my daily life. Drive should be replaced. Replace the drive if the error repeats. this content Retest after checking the connections.

There may be repairable media errors on a platter. Replace the drive if the error repeats. I figured the drive was probably failing, and my next step was to try to run scandisk.

Replace the drive.

What would the fact that it was allowing me to get to a dos prompt before, but not after many restarts indicate? failure and errors How to test a drive for problems using Data Lifeguard Diagnostics for Windows Where to download software, utilities, firmware updates, and drivers for WD products Processing... Replace the drive if the error repeats. Replace Drive 218 10+ SERVO Errors SERVO 10+.

As I recall, there are bootable versions of it. This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection. Extended self-test routine recommended polling time: ( 231) minutes. http://txtbl.com/western-digital/western-digital-0226-error-code.html Check cabling & retest.

Re-Test Drive with latest diagnostic utility 117 Uncorrectable ECC Error Uncorrectable Error Correction Code (ECC) Error. This may be due to an internal error or to a failed connection which did not allow the interrupt command to be sent to the drive properly. This may be due to a media or read/write error. Browse other questions tagged hard-drive hardware-failure smart or ask your own question.

From this point on, the computer is not responsive. windows repair did not work - system not found on this drive or something. The command set to be executed has timed out. Re-test Drive 163 Unknown Error Queued command timed out.

It hit two sectors that had gone bad and it just so happens that these two sectors contain Windows XP's boot files, nothing new that hasn't been backed up. The runtime version will show what is recoverable, but the recovery version will cost something like $80 USD. Answers others found helpful How to tell if the noise or sound the drive is making is normal Understanding S.M.A.R.T. Re-test Drive with appropriate diagnostic utility 202 Drive Not Supported Older Western Digital drives are not supported by the diagnostic utility version being used.

Ensure that you are using the latest version of diagnostic utility and that your cable is in good working condition. tempo72 replied Nov 1, 2016 at 3:38 AM Spam from e.wowcher captharry replied Nov 1, 2016 at 3:17 AM Plugged external DVD drive into... The Identify Drive Command has not received an acceptable response from the drive. Problems with new Western Digital Raptor Drives Can't find your answer ?

All the Western Digital HDD show error 0226: Unable to reallocate sector if I diagnostic with WD HDD diagnostic tool. Re-Test Drive 586 DRQ Timeout Data ReQuest Timeout. The drive has to be replaced. Please re-test the drive with Data Lifeguard.

I was also able to get it to read the windows 98 disc that I have as I tried to see if there was a repair option. I used Ontrack that comes on the boot CD.