Home > Western Digital > Western Digital Error Code 0257

Western Digital Error Code 0257

Why Drive 1? Newer Than: Search this thread only Search this forum only Display results as threads More... Possible fake Xfinity secure wifi detected [ComcastXFINITY] by anon273. Incidently I am using award bios 1.0A version Do you mean to say that I should do an autodetect..it doesnt work though. check over here

Re-Test Drive 108 Seek Not Complete A Seek command did not complete in the time allotted. Check your floppy and retest. The failure to complete the test indicates a failed drive. Re-Test Drive 106 Track 0 Error Track 0 was not properly detected. https://support.wdc.com/knowledgebase/answer.aspx?ID=11711

Join Now For immediate help use Live now! I wonder if their utility is broken. Just assuming. 2. This error can occur on non-Western Digital drives.

Top Western Digital Replacement of Defective Drives by James R. SO help help once again. 0 Message Expert Comment by:ewilson1998-09-19 um did you have FAT 32 formated on that drive with D-space3? 0 Message Author Comment by:KSCHADHA1998-09-19 NO I Retest. Replace the drive if the error repeats.

Re-test with appropriate diagnostic utility 228 DRIVE IS LOCKED-DST FAIL Security feature of the drive reports locked status. Retest the drive. This may be due to a defect. If the hard drive passes, a screen message will say so.

If you know of anyone else who might have this model drive, please pass this information along to them. Replace Drive 585 Busy Timeout During a read verify, a command could not be completed. Version 4.12 for older drives and version 5.00 for current drives. Please ensure that you are using the proper version of diagnostic utility.

Track 0 also holds information about the drive. http://www.dslreports.com/forum/r3821712-New-used-hard-drive-error This may be an anomaly or a defect with the drive. The drive may not have been accessed properly possibly due to a bad connection. If the system cannot properly handle a drive running a specific Ultra ATA rate such as ATA100, the data may become corrupted.

Data sent between the host computer and the drive has been corrupted. check my blog Please re-test the drive with Data Lifeguard. Re-test Drive 134 Busy Timeout Timeout from checking busy bit. Replace Drive 200 Drive Not Tested Supported WD drives are initialized with this status.

I know what the primary and secondary IDE controllers are.. Thanks for any help. #1 Jhill, Feb 21, 2003 dmhinz Member Joined: Jan 24, 2002 Messages: 127 Likes Received: 0 Typically the warranty is attached to the drive and not Replace drive if unable to correct error 120 Unknown Error An unknown error has occurred during testing. this content Then later on the BIOS just refused to recognize the HDD> Can I somehow force-format the disk and recover it Is any such software available.

You may also want to reroute your IDE cable away from sources of electronic bus noise such as your CPU, Power Supply, etc. It may also happen when the wrong version of diagnostic utility is used. The printer may not be attached or turned on.

This may be due to a defect with the drive or a bad connection.

It also may be due to a defective connection. Keep in mind, this will be the third >replacement 1.6 G drive that WD has shipped me in the last 4 months. >Given that, they have always replaced the drives without Re-test Drive 142 TK-TK SEEK ERROR Error encountered during track-to-track seek. psongman 2011-11-21 15:01:30 UTC #3 Hi, well, I got it to work and it repaired all the errors, given an error code of 223.

Yes, My AC31600H drive passed the test. Action to take, re-test driveSo I re-tested the drive this time it said it had problems on it that could be repaired so I tried to repair it. Restore password × Upload manual upload from disk upload from url Thank you for your help! have a peek at these guys Retest after checking the connections.

The only thing to do is get a news board to recover the data. There may be repairable media errors on a platter. If I wanted to format the existing system partition, the format would also stop somewhere at the beginning when attempting to recover "something". Check your connections and replace the cable.

If it is >an AC31600, it will run the tests... >David Could you post that program here please? Retest after checking the connections. Re-Test Drive 11 Cable Test Failed Failure during cable test. Check cable & retest.

Create and use a new DLG Tools diskette. This is Experts Exchange customer support. Retest after checking the connections. Create and use a new DLG Tools diskette.

This error may also appear if the floppy has been infected by a hidden virus. I called their 800 number >(listed in the documentation), gave them the Failure Code Number, and >they said they will send a newer model 1.6 Gb drive within the next 8 Re-Test Drive 258 ECC 10+ Error Correction Code. You could get either.

Re-Test Drive 101 Unknown Error An unknown error has occurred during testing. There is certainly somethong wrong with the disk I used to run win95 with drvspace3 on it. Experts Exchange How to use PRTG for Bandwidth Monitoring using NetFlow or Packet Snifffing Video by: Kimberley In this tutorial you'll learn about bandwidth monitoring with flows and packet sniffing with and it has been my experience that you usually get a larger drive as the replacement.... 0 LVL 1 Overall: Level 1 Hardware 1 Message Expert Comment by:jimat1998-09-19 sounds not