Home > Western Digital > Western Digital Error 0104

Western Digital Error 0104

enabled help you monitor a drive's internal status through diagnostic commands. Re-Test Drive 111 DIAG COMMAND ERROR The drive did not properly respond to test commands. Several instances of track information could not be found. There may be repairable media errors on a platter. http://txtbl.com/western-digital/western-digital-error-status-code-0104.html

Transparent Auto RElocate. Résultats: IRQ TIME OUT ERROR/STATUS CODE 0112 DRIVE NOT READY ERROR/STATUS CODE 0104 Bien évidement cela est arrivé d'un seul coup...je n'ai pas secoué le disque...celui ci a 2 ans...WD est Replace the drive if the error repeats. WDC Support Downloads Knowledge Base Product Registration Warranty Services Contact Ask a Question Contact Support Feedback Other Sites MyCloud.com Online Learning Center CONNECT WD Blog © 2016 Western Digital Technologies, Inc.

Re-test Drive 220 Drive is Locked Security feature of the drive reports locked status. For the last 12 hours i've run chkdsk /R. Some vendors use the security feature to ensure the usage of only specific drives in their system, or the drive may have been locked by a user using a third party But I fear doing this.

An interrupt command to perform a specific task failed to complete. If the error repeats, replace the drive. The drive has to be replaced. The drive has failed and must be replaced.

It also may be due to a defective connection. This may be due to a media or read/write error. Another one is that if I find myself facing a similar issue in the future, I'll never ever resort to do a physical approach to the rescue methodology (no freezer, no Retest after checking the connections.

That way you may be able to recover your data if the problem is located in the mobo. I effectively have to shutdown the VM and terminate all VirtualBox instances before it resets its internal state. At least ten ECC errors have been detected. If you need anything specific please let me know!

Regards, Juan Share this post Link to post Share on other sites TSullivan 0 SR Admin Admin 0 685 posts Posted March 21, 2011 · Report post Well the stuff why not try these out Re-test Drive 206 Memory Allocation Error Unable to allocate memory for program structures. Replace the drive. These are the captures of those two errors.

Replace the drive if the error repeats. check my blog Three questions you need to ask before running these types of programs. 1) Do I actually KNOW what is wrong with the drive. 2) Do I know what issues the software comment:6 Changed 5 years ago by kamalx I observe exactly the same issue as ddan (comment:5) with a 500G Western Digital external hard drive on Mac OS X 10.7.3. Contact System Vendor 221 Test Not Supported Certain older drives do not support certain SMART Self Tests.

Re-test Drive 148 Not Selected Drive not selected. When I ran the diagnostics tool by WD after booting the PC from a DOS USB flash drive I got the following diagnostic: DRIVE NOT READY ERROR/STATUS CODE: 0104. All Rights Reserved. this content Drive should be replaced.

Replace the drive if the error repeats. Do I really need a new Hard Disk?  Enigmaman 2010-05-20 14:46:52 UTC #2 Apologies for typos above. At least ten errors have been detected.

Re-test Drive If an error code is encountered that is not in the list above, please Contact Us for additional troubleshooting.

And I need to choose to boot in a Safe Mode, the last known good setting, or normal mode. Re-Test Drive 106 Track 0 Error Track 0 was not properly detected. Replace Drive 225 Too Many Errors Found Error count reached a threshold value. Replace Drive 358 DAM 10+ Data Address Mark.

I really hope there is some way to get things going again. Also, the Cancel button at this point does not do anything, OK closes the blank dialogs that used to have settings screens in them earlier. Regards. have a peek at these guys Drive should be replaced.

The cable is loose, broken, or not plugged in. Re-test Drive 163 Unknown Error Queued command timed out. The BIOS sees the drive, but when I choose it to see its information everything is blank as if there wasn't any drive data to show. Download in other formats: Comma-delimited Text Tab-delimited Text RSS Feed Contact – Privacy policy – Terms of Use Tech Support Forum Security Center Virus/Trojan/Spyware Help General Computer Security Computer Security News

Drive should be replaced. Replace the drive if the error repeats. Drive should be replaced. Profile of failing 1TB External Drive Change History comment:1 Changed 5 years ago by lectroidmarc Seeing exactly the same with 4.1.0 on both 10.6 and 10.7 host with a Linux client.

Several instances of information on data positioning and location could not be found. Verify that is the issue before trying any 'magic' software to cure a problem that has not been properly diagnosed. After that I would use a copy tool to pull off any data if it was present to another drive. This may be a drive issue, however it may be related to a defective connection.

Also I have no idea how certain things will interact through the USB drive. However I can still run Ubuntu from CD. This may be due to a media or read error. Re-Test Drive 14 Test Suspended A test has been temporarily suspended by the user.

Drive should be replaced. Re-Test Drive 10 Set File Pointer Error A SetFilePointer command during the test has failed.