Home > Western Digital > Western Digital Cable Test Error

Western Digital Cable Test Error

Retest. Version 4.12 for older drives and version 5.00 for current drives. Check cabling and retest. Retest after checking the connections. check over here

would like to close qn and reward points for suggestion 0 Message Active 3 days ago Author Closing Comment by:grnow2011-07-06 pity has to take last resort to send drive to Re-Test Drive 103 Write Fault Error A Write command during the test has failed to complete. Retest after checking the connections. Replace Drive 219 Drive Cable Error Failure during cable test.

Retest after checking connections. going back to my problems: - 11-Cable Test::Read diagnostics sector error - Raw Read error Rate i cant even find a cause braindead, #15 2009/10/19 Arie Administrator Administrator Staff Joined: Re-test the drive with Data Lifeguard. Check Floppy and use appropriate diagnostic utility 209 Self Test Failed To Run SMART Self Test failed to start when executed.

There are too many errors detected on this drive to be repaired. Replace Drive 13 Failed to Repair Sector A test failed to repair bad sectors. This may be an anomaly. Thanks.I ran the provided command and it resulted in an error as below: "Unable to determine volume version and state.

Finally, I installed UBUntu latest version (dual boot) on my home PC and could see everything (all data) flawless without any disturbance. karthik24sOct 19, 2014, 6:55 AM Agera One said: Try what happens in other system/laptop. Check connections and retest. https://community.wd.com/t/11-cable-test-write-sector-error/13087 Could you please elaborate more how to initiate the chkdsk command and repair bad sectors ?

Re-Test Drive 356 DAM 1 Data Address Mark. enabled help you monitor a drive's internal status through diagnostic commands. So, a file of certain (say 10 MB) will not be copied such that it fills cluster 1 then cluster 2 then cluster 3, etc. This error is most likely an internal malfunction of the drive and not related to the condition of the cables etc.

Drive should be replaced. Re-test with appropriate diagnostic utility 228 DRIVE IS LOCKED-DST FAIL Security feature of the drive reports locked status. Replace Drive 218 10+ SERVO Errors SERVO 10+. even after the scandisk i was unable to copy some of the files.

Test Time: 05:59:17, October 19, 2009 Test Option: EXTENDED TEST Model Number: WDC WD5000BEVT-11ZAT0 Unit Serial Number: WD-WXNX08NC5444 Firmware Number: 01.01A01 Capacity: 500.11 GB SMART Status: FAIL Test Result: ABORT Test check my blog Replace Drive 218 10+ SERVO Errors SERVO 10+. http://www.myshopping.com.au/ZM--383653838_Hard_Drives If you object to my “Candourâ€, read another post ! "BENE DICTUM, BENEDICTE !" pcbugfixer, #8 2009/10/19 braindead Inactive Thread Starter Joined: 2009/02/09 Messages: 265 Likes Received: 2 Trophy This may be due to an internal error or to a failed connection which did not allow the interrupt command to be sent to the drive properly.

Check your floppy and retest. So the needle takes more time to find the data when the HDD is spinning at 5400 pm and takes less time when spinning at 7200 rpm)."Thus, a/set of damaged cluster/sectors Replace the drive if the error repeats. this content although i could view them with Vista default picture viewer: im assuming those pictures are unrecoverable.

kevinrs 2010-01-07 22:31:59 UTC #11 I'm at 5 days since I responded to support that I changed the cable with no change in the errors, with no further response from them. This may be due to a media error. Back up as soon as possible before the drive completely fails and the data will become UNRECOVERABLE.

Replace Drive 215 2-9 IDNF Errors Identified Data Not Found (IDNF) 2-9.

If there is some physical damage on the drive(physical bad sectors as well) this method may help. Status code = 04 (Unknown failed test element), Failure Checkpoint = 96 (Unknown Test) SMART self-test did not complete on drive 4! Re-Test Drive 20 Failed to Delete Partitions A Device I/O Control command during the test has failed. Re-test Drive 201 Non-WD Drive The drive does not have a WD serial number.

Replace the drive. All Rights Reserved. You are viewing our forum as a guest. have a peek at these guys Drive should be replaced.

Replace the drive if the error repeats. ppg113, #7 2009/10/19 pcbugfixer Inactive Joined: 2009/09/28 Messages: 273 Likes Received: 2 Trophy Points: 108 Location: Condell Park (Sydney) NSW, AU Computer Experience: Experienced G'Day "braindead", Is this the drive you Replace Drive 225 Too Many Errors Found Error count reached a threshold value. Replace the drive if the error repeats.

Ten or more instances of information on data positioning and location could not be found. An onboard defect counter has determined the drive has too many errors and should be replaced. Replace the drive if the error repeats. Test Time: 06:31:03, October 19, 2009 that laptop has a history with USB devices (not enough power), so i guess that is the cause of our problem.

Replace the drive if the error repeats.