Home > Western Digital > Wd Test Error Code 08

Wd Test Error Code 08


Also! To learn more and to read the lawsuit, click here. Auto Offline data collection on/off support. Short self-test routine recommended polling time: ( 2) minutes. navigate here

The open file operation will fail with error -1032 (0xfffffbf8). Replace the drive if the error repeats. Also! Re-Test Drive 19 SMART Enabled Operation Failure Self-Monitoring, Analysis, and Reporting Technology (SMART) Enable Operation failed.

Unable To Repair Bad Sectors

This may be due to a media or read error. Ignore the Threshold. No, that's just for some european countries - EU, not for other countries in Europe which are out of EU, i explained that before, cause i tried through that link for How Does a computer get Infected?

If the error repeats, replace the drive. Check cabling & retest. The printer may not be attached or turned on. Read Smart Attribute Command Error On Drive 2 I would advice you to try both and work with the clone and the image(do not write on the original HDD).If the cloning option encounters an error, it will ask you

Finally, I installed UBUntu latest version (dual boot) on my home PC and could see everything (all data) flawless without any disturbance. Smart Offline Immediately Command Error On Drive 1 Please ensure that you are using the appropriate version of diagnostic utility. General Purpose Logging supported. http://answers.microsoft.com/en-us/windows/forum/windows_8-update/test-error-code-08-error-was-detected-while/5398a7cd-7a05-492c-9172-796aecebcc9d Retest after checking the connections.

It also may be due to a defective connection. Status Code 07 Failure Checkpoint 97 CONTRIBUTE TO OUR LEGAL DEFENSE All unused funds will be donated to the Electronic Frontier Foundation (EFF). Check connections and retest. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity

Smart Offline Immediately Command Error On Drive 1

Replace drive if unable to correct error 120 NO DRIVE FOUND Cannot communicate with drive. Retest after checking the connections. Unable To Repair Bad Sectors There may be repairable media errors on a platter. Western Digital Quick Drive Test Failed Check Floppy and use appropriate diagnostic utility 209 Self Test Failed To Run SMART Self Test failed to start when executed.

but always same results- bad sectors with no recovery option, S.M.A.R.T notified many errors, and error 08 says this disk has to be replaced, but no solution by WD official distributor http://txtbl.com/western-digital/western-digital-extended-test-error-code-08.html If you have a question relating the what's going on in the community, we will be happy to respond. Please ensure that you are not loading any other DOS level files from the floppy prior to running diagnostic utility. You may need to rescan to ensure that the repairs were effective. Western Digital Error Codes

If there is any direct software available I can use it .. Normally that i contacted firstly WD support, they don't have chat option, like other serious companies, for cases like my, urgent situation, then i wrote them mail, and what i get,  Thanks.I ran the provided command and it resulted in an error as below: "Unable to determine volume version and state. his comment is here karthik24sOct 18, 2014, 1:22 PM Agera One said: The drive is really very bad.

There could be media errors present on this drive. Western Digital Bad Sector Repair If the error repeats, replace the drive. As for Amazon being a really good online retailer when it comes to customer service, I have found NCIX.com (Netlink Computers Incorporated, the x is just there because someone took NCI

Conveyance self-test routine recommended polling time: ( 5) minutes.

There were media errors that were within the repair capabilities of diagnostic utility. Accept the License, Right Click on the drive to test, Pick Diagnostics, The Run the Quick test and the Extended test. solved Hard Drive going to die ?Pls help solved Is my storage going to die soon? Too Many Bad Sectors Detected Re-Test Drive 102 Seek Timeout A Seek command did not complete in the time allotted for its completion.

I understand your point, however programming is diffiicult and there are people who wrote the code and the instructions.  People make mistakes all the time, it's in human nature.  If someone Re-test Drive 142 TK-TK SEEK ERROR Error encountered during track-to-track seek. This may be due to a media or read/write error. weblink However, I recently tested the hard drive for errors with WD's Lifeguard tool.

But however i asked WD support what they suggest me to do, cause ERROR 08 dissapered on Extended test after ZERO format. WD Acronis: http://support.wdc.com/product/downloaddetail.asp?swid=119Hope this will help,D_Know_WD karthik24sOct 21, 2014, 4:03 AM D_Know_WD said: Hi there karthik24s,Too many bad sectors could be the reason for the issues you are facing. This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection. Roger ____________________________ MiniToolBox by Farbar Version: 21-07-2014 Ran by RK (administrator) on 04-10-2014 at 18:37:46 Running from "F:\Documents and Settings\RK\My Documents\Downloads" Microsoft Windows XP Professional Service Pack 3 (X86)

The drive has not responded to the SMART test request. Replace the drive if the repair fails. Ask ! Drive should be replaced.

Please re-test the drive with Data Lifeguard. Does it tell you anything? The HDD stores it randomly over the entire storage. (that's why the HDD platters spins while doing work, the needle detects where the data are stored along the rotating platters. The same utility and the original code used to lock the drive are necessary to unlock this drive.

Ten or more instances of track information could not be found. The drive is defect free. The drive has to be replaced. Retest.

What does this mean ?