Home > Western Digital > Wd Hdd 08-error Was Detected While Repairing Bad Sectors

Wd Hdd 08-error Was Detected While Repairing Bad Sectors


This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection. Since I was unable to do a reimage via the hard disk and get to the “Dell Factory Image Restore” option I used the DVD. Replace Drive 0009 - 0014 SMART Error Self-Monitoring, Analysis, and Reporting Technology (SMART) Error returned during SMART Status/Self Test Command. Drive should be replaced. http://txtbl.com/western-digital/wd-diag-error-08.html

Ten or more instances of track information could not be found. Re-test Drive 140 DRQ TIMEOUT ECC The drive did not properly respond to test commands. It also may be due to a defective connection. Self-test supported. check this link right here now

Unable To Repair Bad Sectors

Sounds like your better off buying a new driver, install windows, and start from scratch. Please contact the system vendor for the above-mentioned information. My Config is :-AMD FX 6300Corsair Vengeance 8 GBSeasonic ECO 600What should I do ? Please re-test the drive with Data Lifeguard.

Re-Test Drive 14 Test Suspended A test has been temporarily suspended by the user. James Litten -- I ran Gsmartcontrol and here is the output on the drive in question. This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection. Read Smart Attribute Command Error On Drive 2 Retest after checking the connections.

As a guest, you can browse and view the various discussions in the forums, but can not create a new topic or reply to an existing one unless you are logged Both successful & unsuccessful attempts are counted. #12 czesiu, Sep 29, 2010 czesiu Member Joined: Feb 25, 2009 Messages: 43 Likes Received: 0 so this one is more important: 5,Reallocated If it got worse then toss the drive. i thought about this i used it just for storage, and it wasn't used often!

This may be due to a media or read/write error. Western Digital Quick Drive Test Failed Could this be linked to a bad power suply? If it can't recover the data it then gives up and counts it as a Uncorrectable Sector or Bad Sector and depending on where it is it can cause a lot Please advice about the same. 8 answers Last reply Aug 30, 2013 More about hard disk failing d1rtyju1c3Jan 1, 2012, 8:51 PM I would RMA.

Test Error Code 08 Western Digital

Replace Drive 218 10+ SERVO Errors SERVO 10+. MHDD 4.6 Precise diagnostic of the mechanical part of a drive, perform Low-level format, Bad Sector Sepair, access raw sectors, manage S.M.A.R.T. (SMART) and other drive parameters such as acoustic management, Unable To Repair Bad Sectors Conveyance self-test routine recommended polling time: ( 5) minutes. Smart Offline Immediately Command Error On Drive 1 There's also Ubuntu persistant you should be able to do from a flash drive.

There may be repairable media errors on a platter. check over here Sectors! :wink: The hard drive firmware has probably done that for you already. Check Floppy and use appropriate diagnostic utility 207 Critical Resource Error Unable to locate and/or use a system resource (e.g. - printer). File record segment 30698 is unreadable. Western Digital Error Codes

Replace the drive if the error repeats. Re-test Drive 206 Memory Allocation Error Unable to allocate memory for program structures. Re-Test Drive 17 Erase SSD Failure A write command during the test has failed. his comment is here Replace Drive 219 Drive Cable Error Failure during cable test.

The same utility and the original code used to lock the drive are necessary to unlock this drive. Status Code 07 Failure Checkpoint 97 I ran the ""Scan for and attempt Recovery of Bad Sectors" and was so pleased how much seemed to be being repaired. Retest the drive.

Re-Test Drive 108 Seek Not Complete A Seek command did not complete in the time allotted.

Check your floppy and retest. The drive has not responded in the time allotted. This condition occurs when the device's SMART reliability status indicates an impending degrading or default condition. Western Digital Bad Sector Repair Started by anonanon , Jan 09 2013 09:05 PM Page 1 of 3 1 2 3 Next Please log in to reply 38 replies to this topic #1 anonanon anonanon Members

Track 0 on the drive must be accessed to perform parts of various internal tests. There were too many errors found on this drive to be repaired. The system returned: (22) Invalid argument The remote host or network may be down. weblink Replace the drive if the error repeats.

or read our Welcome Guide to learn how to use this site. Replace Drive 208 SMART status failed after the media scan. Several instances of information on data positioning and location could not be found. Replace the drive if the error repeats.

The drive has not responded to the SMART test request. Check cable & retest. lol Happy New Year Back to top #16 Blackredgold1964 Blackredgold1964 Member Members 20 posts Gender:Male Posted 05 January 2013 - 04:46 PM So, new HD installed, all Vista and drivers installed dish_mooseJan 1, 2012, 11:42 PM If there is physical damage no software is going to fix it - free or not.-RMA now - save yourself a headache.-Bruce d1rtyju1c3Jan 1, 2012, 11:43

Hello I was playing L4D on my Vista 64 yesterday like any normal person, but then the game started stuttering Thread Tools Search this Thread 10-26-2009, 03:24 PM #1 WDC Support Downloads Knowledge Base Product Registration Warranty Services Contact Ask a Question Contact Support Feedback Other Sites MyCloud.com Online Learning Center CONNECT WD Blog © 2016 Western Digital Technologies, Inc. The cable is loose, broken, or not plugged in. Count of "unstable" sectors (waiting to be remapped, because of unrecoverable read errors).

Replace Drive 207 SMART status failed before the media scan. Re-Test Drive 10 Set File Pointer Error A SetFilePointer command during the test has failed. Drive should be replaced. Apologies for the length of this post but I thought it’s best I describe all steps I’ve taken.

Several instances of information on data positioning and location could not be found. Replace the drive if the error repeats. Error: (10/04/2014 09:54:43 AM) (Source: Microsoft Antimalware) (User: ) Description: The support for your operating system has expired. I'll put the Speccy output in a separate post.