Home > Wd Error > Wd Error Code 223

Wd Error Code 223

This error may also appear if the floppy has been infected by a hidden virus. Ask ! Version 4.12 for older drives and version 5.00 for current drives. Thanks for your time and reply, ispalten. :) Reports: · Posted 5 years ago Top ispalten Posts: 6259 This post has been reported. http://txtbl.com/wd-error/wd-error-code-0116.html

I'd be grateful if you can compare the the two drives for me -- as I'm not too good at this -- and let me know if there's any difference in Please ensure that you are using the version of diagnostic utility corresponding to either newer or older Western Digital drives. Umm.. Re-Test Drive 115 ICRC Error Ultra DMA CRC error.

SERVO is data on track location. Re-test Drive 134 Busy Timeout Timeout from checking busy bit. Re-Test Drive 102 Seek Timeout A Seek command did not complete in the time allotted for its completion. Ten or more instances of information on data positioning and location could not be found.

Replace Drive 211 2-9 Uncorr ECC Errors Error Correction Code (ECC) 2 through 9. This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection. Re-test Drive with appropriate diagnostic utility 202 Drive Not Supported Older Western Digital drives are not supported by the diagnostic utility version being used. Replace the drive if the error repeats.

ECC is a hardware correction technique that corrects errors. It also may be due to a defective connection. ECC is a hardware correction technique that corrects errors. Re-Test Drive 4 Open Drive Failure Cannot communicate with drive.

Re-test Drive 201 Non-WD Drive The drive does not have a WD serial number. This is the pretest initialization code which indicates a drive is ready to be tested, but has not yet been tested. Thanks. Reference: http://support.microsoft.com/?kbid=311902 Reference: http://forum.ts.fujitsu.com/fo.....38;start=0 Need to procure another brand of HD.

Drive should be replaced. http://error.code.223.western.digital.pcfastbrowser.com/ acrufox 2011-03-15 05:38:27 UTC #5 Would that be the same as booting off a pen drive with dos? Retest after checking the connections. EDIT2: Different drive worked, but had bootup problems. :X Last edited: Nov 10, 2010 Cerulean, Nov 10, 2010 Cerulean, Nov 10, 2010 #2 Nov 10, 2010 #3 drescherjm [H]ardForum Junkie

Ensure that you are using the latest version of diagnostic utility and that your cable is in good working condition. http://txtbl.com/wd-error/wd-error-code-0008.html The information file, which holds the data pertaining to this drive, is corrupted or missing. This may be a drive issue, however it may be related to a defective connection. Retest after checking the connections.

It also may be due to a defective connection. No problem, raphoenix. Replace the drive if the error repeats. his comment is here Re-test Drive 201 Non-WD Drive The drive does not have a WD serial number.

Retest after checking the connections. This may be due to a media error. This condition occurs when the device's SMART reliability status indicates an impending degrading or default condition.

ViVard and GSmartControl for Quick/Extended/Conveyance tests came out clean and error-free.

It also may be due to a defective connection. If ECC occurs, use Data Lifeguard for additional error correction. Check cabling and retest. Re-Test Drive 105 BUSY GLITCH The drive did not properly respond to test commands.

Re-Test Drive 2 SMART Attribute Over Threshold Self-Monitoring, Analysis, and Reporting Technology (SMART) threshold exceeded condition. Board index The team • Delete all board cookies • All times are UTC [ DST ] Powered by phpBB Forum Software © phpBB GroupStyle by Marc Alexander © x BrowseBrowseInterestsBiography Here's the link: WD800AAJB The only difference in the picture is that this drive is Blue. weblink and S.M.A.R.T.

Several instances of track information could not be found. It also may be due to a defective connection. So, filesystem doesn't make any difference? Replace Drive 550 Abort Cmd Abort Command.

enabled help you monitor a drive's internal status through diagnostic commands.