Home > Wd Error > Wd Error Code 0132

Wd Error Code 0132

Check Floppy and use appropriate diagnostic utility 209 Self Test Failed To Run SMART Self Test failed to start when executed. Unfortunately, it can't seem to read any of the cylinders.I was kind of concerned that maybe I didn't hook up the drive correctly when I put it in the computer, but tool" the only problem is that I did... Forster (1909)Barry Schwartz TED Talk: "The Paradox of Choice" (Featuring the True Secret to Happiness) Top yewbie Posts: 208 Joined: Mon Sep 13, 2010 6:35 pm UTC Re: Diagnosing a Kaput navigate here

Re-test Drive 162 READY EXPECTED Timeout from checking busy bit. Replace Drive 161 RESET SIGNATURE The drive did not properly respond to test commands. An error was reported by the drive during the Write command (to cause the auto-relocation) or the Read Verify command (to verify the relocation happened). Check your floppy and retest. https://support.wdc.com/knowledgebase/answer.aspx?ID=11711

The drive has not responded back in the time allotted. Post navigation Previous PostPast Tense Errors ExamplesNext PostSnoopy Errori Search for: Proudly powered by WordPress The Mother Board Motherboards.org forums. Track 0 also holds information about the drive.

Check cabling and retest. Replace the drive if the error repeats. Please ensure that you are using the version of diagnostic utility corresponding to either newer or older Western Digital drives. Retest after checking the connections.

It also may be due to a defective connection. This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection. A number of ECC errors (between 2 through 9) have been detected. http://www.techsupportforum.com/forums/f16/solved-what-is-error-status-code-0132-from-data-lifeguard-diagnostics-537960.html It ran about an hour and came up with Error Code 223, and said it repaired all the problems.

Re-test Drive 136 Bad Sector Sector Marked Bad Error. This may be due to a media or read/write error. This error may have internal and external reasons. Replace the drive if the error repeats.

Commit interval 5 seconds[ 85.990807] EXT3-fs: mounted filesystem with ordered data mode.[ 97.002795] ata1.01: status: { DRDY ERR }[ 97.002837] ata1.01: error: { ABRT }[ 97.025711] ata1.00: configured for UDMA/100[ 97.034414] Replace the drive if the error repeats. It also may be due to a defective connection. This may be an anomaly or a defect with the drive.

Re-test Drive 220 Drive is Locked Security feature of the drive reports locked status. http://txtbl.com/wd-error/wd-error-code-0139.html The command set to be executed has timed out. Re-test Drive with appropriate diagnostic utility 202 Drive Not Supported Older Western Digital drives are not supported by the diagnostic utility version being used. Replace the drive if the error repeats.

and get an RMA if still in force. Last edited by terrannova; March 1, 2010 at 17:16. Re-Test Drive 356 DAM 1 Data Address Mark. his comment is here SERVO is data on track location.

I have pictures and files on there that I would like to salvage. Not just that you will save money, you will as well hone your technical skills. Replace Drive 585 Busy Timeout During a read verify, a command could not be completed.

Replace the drive if the error repeats.

Check cabling and retest. Quick response time. Check cable & retest. It did this about 4 times and then it would say that it failed.

Re-Test Drive 16 Random Read Error A read command during the test has failed. When the problem is not taken care at the earliest opportunity, tendency is it will worsen and you don't want that. Retest. http://txtbl.com/wd-error/wd-error-code-223.html Replace the drive.

Sense: No additional sense information[ 79.662279] end_request: I/O error, dev sdb, sector 0[ 79.662288] ata1: EH complete[ 79.662299] unable to read partition table[ 79.662364] sd 0:0:1:0: [sdb] Attached SCSI disk[ 79.662489] This error may also appear if the floppy has been infected by a hidden virus. Some vendors use the security feature to ensure the usage of only specific drives in their system, or the drive may have been locked by a user using a third party Retest after checking the connections.

An onboard defect counter has determined the drive has too many errors and should be replaced. The great thing to do is open the computer in safe mode so that you can uninstall the software recently added, also take away any hardware devices linked to it. There are too many errors detected on this drive to be repaired. Replace your cable and retest the drive.

There were media errors that were within the repair capabilities of diagnostic utility. If ECC occurs, use Data Lifeguard for additional error correction. GTX 680 High temps $1200 for 1 of these 3 options [SOLVED] Internal HD Used as External HD Job interview Clinton's (hacked) e-mail Server Video streaming on smarttv No WMA both You may need to rescan to ensure that the repairs were effective.

Re-test Drive 141 UNKNOWN ERROR An unknown error has occurred during testing.