Home > Wd Error > Wd Error Code 0104

Wd Error Code 0104

Retest after checking the connections. The drive has not responded to the SMART test request. Re-Test Drive 115 ICRC Error Ultra DMA CRC error. This may be due to a media or read/write error. navigate here

Contact Us StorageReview.com Community Software by Invision Power Services, Inc. × Existing user? This error is most likely an internal malfunction of the drive and not related to the condition of the cables etc. A number of ECC errors (between 2 through 9) have been detected. This error may also appear if the floppy has been infected by a hidden virus.

This may be due to a media error. If the automatic repair feature is unable to repair these errors, replace the drive. Replace Drive 558 SERVO 10+ SERVO is data on track location. Replace the drive if the error repeats.

so i reboot, but i found the drive just went fail bios detect the drive but it showing 0mb i ever bring the drive the local hdd service center, its just Re-Test Drive 11 Cable Test Failed Failure during cable test. Do I really need a new Hard Disk?  Enigmaman 2010-05-20 14:46:52 UTC #2 Apologies for typos above. Several instances of information on data positioning and location could not be found.

Share this post Link to post Share on other sites slyphnier 3 Member Member 3 83 posts Posted March 28, 2011 · Report post Hello, Since I couldn't do anything Drive should be replaced. Replace Drive 211 2-9 Uncorr ECC Errors Error Correction Code (ECC) 2 through 9. Replace Drive 557 SERVO 2-9 SERVO is data on track location.

If the error repeats, replace the drive. The BIOS sees the drive, but when I choose it to see its information everything is blank as if there wasn't any drive data to show. Besides that, I think I've learnt some useful lessons with this experience. It may also happen when the wrong version of diagnostic utility is used.

After the problem happened, I took it out of the USB enclosure and I moved it into another PC. Re-Test Drive 111 DIAG COMMAND ERROR The drive did not properly respond to test commands. There were media errors that were within the repair capabilities of diagnostic utility. This may be due to a defect with the drive or a bad connection.

It also may be due to a defective connection. http://txtbl.com/wd-error/wd-error-code-0258.html I run a scan disk from Windows XP and it does not report anything wrong. Given one of my HP boot options I could get a blue screen with the the Unmountable_Boot_Volume error. Just stuff like CP for filesystem-level or DD for block level depending on the damage of the drive.

That way you could mount the drive as read only and see if the data appears. It feels like this is a SW issue given the way it crashed but what do I know. No Errors 101 Unknown Error An unknown error has occurred during testing. http://txtbl.com/wd-error/wd-error-code-223.html Replace the drive if the error repeats.

Sometimes it works, other times things can error out. One last question: does it make any sense to try to open the drive? At least ten ECC errors have been detected.

To run in ATA 66 and ATA100 rates, an Ultra ATA 80 -conductor cable must be used.

Drive should be replaced. Upon reboot I get a black DOS screen telling me that windows failed to start. Retest after checking the connections. Replace the drive.

The drive has not responded in the time allotted. Some vendors use the security feature to ensure the usage of only specific drives in their system, or the drive may have been locked by a user using a third party Retest after checking the connections. weblink Replace Drive 256 ECC 1 Error Correction Code.

You may have to register before you can post: click the register link above to proceed. I'm going to install it in another hard drive that I am not using right now (one with 320 GB) as you suggest. Does the BIOS show the drive as being OK? Re-Test Drive 121 Servo Error Servo error.

Replace the drive if the error repeats. This error can occur on non-Western Digital drives. Regards, Juan Edited March 30, 2011 by Elohssa Share this post Link to post Share on other sites Prev 1 2 Next Page 1 of 2 Create an account or Replace the drive if the error repeats.

Check your floppy and retest. Share this post Link to post Share on other sites FastMHz 9 Member Member 9 408 posts Location:Hagerstown, MD, USA Interests:Technology, Electricity, Solar Posted March 27, 2011 · Report post The printer may not be attached or turned on. Retest.

I'm not sure of this, of course, but I think that if I had been a little more patient and had kept trying the software way, I would probably have found This may be due to a media or read/write error. Retest after checking the connections. This may be due to a media error.

It also may be due to a defective connection. Replace the drive if the error repeats. Re-Test Drive 102 Seek Timeout A Seek command did not complete in the time allotted for its completion. The All Programs groups are not all there (only about 1/4 of them).

Self-Monitoring, Analysis, and Reporting Technology (SMART). This may be an anomaly.