Home > Unable To > Cannot Connect To Nsr Service

Cannot Connect To Nsr Service

Contents

A reasonable rule of thumb for internal length is to assume 1 meter of internal bus length for the workstation chassis and about 0.25 meters per device for external peripheral boxes. Backup BlogProduct DirectoriesEdit These Directories!Backup SoftwareBackup and Archive HardwareBackup Book WikiMiscellaneous ResourcesBackup Service ProvidersMailing ListsFAQsEdit These FAQs!NetBackup FAQNetWorker FAQTSM FAQForumsJoin Our Forums!General TopicsBakBone NetVaultCA Brighstor ARCserveCommVault GalaxyEMC NetWorkerHP Data ProtectorIBM TSMSymantec To prevent tape write errors, clean your tape drive regularly and use only data- quality tapes. It is not then networker is not running.

Xview Errors If you receive the following error message when you attempt to start the graphical administration interface with nwadmin from a client machine, it means that the client is not Diagnostic Report Backup includes a script called nsr_support that generates an exhaustive diagnostic report. Backup servers provide a backup and recover service. Deinstall the driver according to the instructions shipped with the old driver, then reinstall the latest version. have a peek at these guys

Too Many Indications Attempted - Discarding One

Use ping to establish basic connectivity. A client alias change is needed for the following situations: Machines that have two or more network interfaces Sites that mix short and "fully qualified" hostnames for the same machines; for It appears that automatic index management according to the browse and retention policies does not occur. Halting a Network Backup To stop running a network-wide backup using the Backup X Windows interface, use the Stop button in the Group Control window.

The next network-wide backup will

How to Set Up Host Tables SunSoft recommends that you troubleshoot IP problems using only host tables. The nsrexecd daemon allows you to restrict access to a select set of Backup servers. For example: --------------------------- # savegrp -p group_name --------------------------- shows you a backup preview of the clients assigned to the backup group group_name. Length of tape Be sure to verify tape lengths.

The host tables reside in /etc/hosts. Networker Unable To Send Indication To Jobs Verify that the Media Type attribute in the Devices resource matches the expected media for your device, and make corrections if needed. Re: nsrjb: cannot connect to nsr service David Hampson Feb 8, 2011 12:51 AM (in response to PatrickLee) From memory you go to the Media menu, click Devices, find the device anchor The device name must belong to a tape drive in the autochanger, not the autochanger itself.

Close Box Join Tek-Tips Today! This information can be retrieved by going back to the n/w server where the tape was created from. You can add or remove user names, depending on the level of security the files require. However, in the Clients resource where these configurations are applied, Backup automatically replaces the selected configuration with the preexisting Default configuration.

Networker Unable To Send Indication To Jobs

Please try the request again. To verify media, nsrmmd must reposition the volume to read previously written data. Too Many Indications Attempted - Discarding One Add Stickiness To Your Site By Linking To This Professionally Managed Technical Forum.Just copy and paste the BBCode HTML Markdown MediaWiki reStructuredText code below into your site. Legato back-up solutions 98519:save: Unable To Setup Direct Save With Server To configure host tables on a server or client: 1.

On Solaris, the rpcbind daemon must be running. Make sure the servers file on a client contains both the short name and long name of the server you want to back up that client's data. If Backup is able to find the correct position, media verification succeeds and a successful completion message appears. --------------------------------------------------------------- media info: verification of volume "jupiter.007" volid 30052 succeeded. --------------------------------------------------------------- In this Remotely log in to the Backup server and issue the setenv command at the shell prompt. ------------------------------------- # setenv DISPLAY client-name:0.0 ------------------------------------- For command shells other than csh: ------------------------------- # export

See "Installing the Client Software" in the appropriate chapter for your platform for more information on nsrexecd. Was the Backup command successful before you made any changes, and if so, what changes did you make? File Changed During Backup Backup backs up the image that is in the filesystem at the time it comes across the file. http://txtbl.com/unable-to/cannot-file-lck-open-service.html Backup Backup and Recover This section explains how to troubleshoot various problems you may encounter with Backup backup and recover operations.

Verify that the media cartridge is correctly installed in the autochanger and that the autochanger door is closed. 2. On the Backup server, list the Backup server itself and all of its clients, for example: ------------------------------------------ 127.0.0.1 localhost loopback 123.456.789.111 server server.domain.com 123.456.789.222 client client.domain.com ------------------------------------------ 3. Talk With Other Members Be Notified Of ResponsesTo Your Posts Keyword Search One-Click Access To YourFavorite Forums Automated SignaturesOn Your Posts Best Of All, It's Free!

So I am scanning it for just that ssid, which is only 1 client (which I have re-created, along with the pool that this tape is in).

Checked by AVG anti-virus system (http://www.grisoft.com). Cannot Print Bootstrap Information If your bootstraps are not being printed, you may need to enter the printer name as a hidden attribute using the following steps: 1. Report Abuse Like Show 0 Likes (0) 6. how can I load my tape into the SDLT320 drive on my storage node?

Inspect the following items to verify that the autochanger is properly connected. Autodetected SCSI Jukebox Option Causes the Server to Hang If you install an Autodetected SCSI jukebox using jb_config and the server hangs, the following workaround is recommended: 1. inquire scsidev < at > 3.6.0:QUANTUM SDLT600 3535|Tape, \\.\Tape2147483645 S/N: QD0912AMC00220 ATNN=QUANTUM SDLT600 QD0912AMC00220 WWNN=500E09E000186FCE PORT=00000001 scsidev < at > 4.6.0:QUANTUM SDLT320 6060|Tape, \\.\Tape2147483646 S/N: QDK02Y0034 ATNN=QUANTUM SDLT320 QDK02Y0034 IENN=00E09E60001853B9 WWNN=500E09E0001853B9 To correct this situation do the following at the client machine: ------------------------------------ client% xhost ------------------------------------ Remotely log in to the Backup server and run the following command at the server