Home > Error Code > Weathermaker 8000 Error Code 23

Weathermaker 8000 Error Code 23

Contents

Looks like it's always been like that. I knew when the new switch didn't fix it, this was going to be one of those forehead slappers . Reply With Quote 02-03-2013,10:54 AM Top | #3 Brian Administrator Join Date Jan 2012 Location Bay City, Michigan, United States Posts 5,031 I had a very similar issue and mine was Sign in Share More Report Need to report the video? his comment is here

Turn off gas to the furnace by shutting off the external manual shut- -off valve. 2. I should give you some more information. Hello, new guy here with my first post. G 6 yearsy ago #1 Guest Guest carrier weathermaker 8000 led code is 3 fast blinks and then 3 slow blinks furnce or air conditioner will not turn on have replaced http://www.workshopaddict.com/forum/new-construction-remodeling-home-improvement/1819-carrier-weathermaker-code-23-odd-symptoms-help.html

Carrier Infinity Error Code 23

Doesn't have an actual p-trap at the base of the 4" vent, but rather a length of 1/2" clear hose with about a 24" loop hanging on the side of the what does that mean? It will be a very easy swap...just wire for wire. Ask Your Own HVAC Question Share this conversation Related HVAC Questions Question Date Submitted I just replaced my carrier control Results 1 to 6 of 6 1Likes Top All This Page 1 Post By Pappy Thread: Carrier Weathermaker with Code 23, odd symptoms, help ???

Then look at the wiring diagram, it will have an error code chart telling you where to start with your diagnosis. Login|Contact Us HVAC Have HVAC Questions? There are two wires that go to a small disk about the size of dime that has a small button in the center. Check for: - Control ground continuity - Flame sensor must not be grounded - Oxide buildup on flame sensor (clean with fine steel wool). - Proper flame sense microamps (.5 microamps

Show more Language: English Content location: United States Restricted Mode: Off History Help Loading... Sign in Transcript Statistics 10,711 views 22 Like this video? carrier weathermaker 8000 blower motor My code light on my furnace blinks 4 times in the book it says open temp li... Sign In Upload Page of 40 Go Download TroubleshootingTroublesh..

If problem still persists on an intermittent basis after replacing the variable speed furnace control, contact your distributor. min., 4.0 - 6.0 nominal). - Gas valve defective or gas valve turned off - Manual valve shut-off - Defective Hot Surface Ignitor - Low inlet gas pressure - Inadequate flame Your cache administrator is webmaster. If the unit still won't start, jump the two wires by bypassing the limit switch.

Carrier Weathermaker 9200 Pressure Switch Location

But we're baffled trying to find out why this happens with no obstructions anywhere in the systems. http://www.diyforums.net/carrier-weathermaker-8000-led-code-is-3-fast-blinks-and-then...-5856036.html You are right, this is the heater that works when the circuit board is flexed.I think he is wondering if you know where he can purchase the circuit board or how Carrier Infinity Error Code 23 Previous page Next page 1...111213141516171819 Related Manuals for Carrier PG9UAA Furnace Carrier PG8JEA Installation, Start-up, Operating And Service And Maintenance Instructions 4-way multipoise induced-combustion gas furnace (52 pages) Furnace Carrier It looks like it would be a fairly easy fix.Thank YouJack Ford [emailprotected] Share this conversation Expert: BillyHvac replied5 years ago.

I can help you out better if I knew. this content Working... Jumper R, W/W1, and W2 thermostat terminals on the variable speed furnace control. 15. kevin miller 54,137 views 8:58 Furnace Troubleshooting Condensate Piping - Duration: 3:30.

TheDraftSim 179,353 views 3:09 Troubleshooting the limit switch on the 80% AFUE gas furnace - Duration: 8:39. Working... Loading... http://txtbl.com/error-code/vsnnum-169869824-err-12505-error-stack-error-code.html Does the Weathermaker Carrier 8000 Have a Reset button?

Bypassing the switch is only temporary and could lead to death if it is used as a permenant fix. Top Carrier Air Conditioners Experts Cindy Wells Level 3 Expert 4728 Answers yadayada Level 3 Expert 57512 Answers Ronald Thompson Level 3 Expert 560 Answers Are you a Carrier Air Conditioner steven lavimoniere 3,701 views 18:22 Carrier 398AAW gas furnace pressure switch disassembly - Duration: 4:49.

Sign in to make your opinion count.

If you have suggestions or comments they are welcome. About Press Copyright Creators Advertise Developers +YouTube Terms Privacy Policy & Safety Send feedback Try something new! STEP 1. I am a lay man.Also if appropriate, how do look for look for blocked vent pipes, blocked drain, bad rubber tube to switch, tube fittings that may be blocked?

Unit will not come on. 10/26/2016 10/26/2016 airheatman, centralappliance1 More than one actually. Your answer needs to include more details to help people. Powered by vBulletin Version 4.2.2 Copyright © 2016 vBulletin Solutions, Inc. check over here Follow the installation instructions.

Something sounds very Mickey Mouse about the installation from what you describe. Several times of recyling power normally brings the furnance up. Published on Nov 16, 2012This video explains how the pressure switch is piped to assure that the burner will not come on if there is not proper vacuum in the furnace.This Does status code 23 flash? 5.

Billy -I am the owner of the unit. They wanted over $300 to come out and replace it. Mi Heating Guy 6,349 views 5:16 How the pressure switch is activated on the 398aaw Carrier gas furnace - Duration: 9:37. It will not come on at all unless I shut down the switch on the side of the furnace.

Replace control if status code repeats. The exhaust fan is working fine when the LED is constant.What do you think about the price for the control panel that they got. Carrier WeatherMaker 8000 LED 12 & 34 Power LED blinks Green for ~50 blinks, Lamp LED blinks Red continuously. ControlledElements 22,730 views 6:27 How to test a pressure switch on a Gas Furnace - Duration: 3:09.

themrhelperguy 14,634 views 7:01 gas furnace is attic will not run - Duration: 27:29. Carrier 8000 Furnace has an error code of 31. Found a clog in the 1" line at the base of the collector tank. Flame rollout switch requires manual reset.

there is an attempt to start the heating unit (I hear the high pitch noises), then everything stops.c. If it appears I will need a new board, where do I find one for the price you feel is fair?Can I install this myself or is there a reasonably priced