Home > Error Code > Wd Hdd Error Code 0223

Wd Hdd Error Code 0223

Contents

Version 4.12 for older drives and version 5.00 for current drives. So I ran Western Digital diagnostic as well. Non-WD drives are not supported. Re-Test Drive 107 Check Sum Error Accumulated test data on the drives is corrupted. navigate here

This drive is the first drive I've ever encountered where dlgdiag just reports errors and fixes them only to say/do the same thing again next time I run it. General Purpose Logging supported. moon1 2011-03-15 12:20:18 UTC #7 the way i see it, you can replace it, because it has bad sectors, and its not able to be fixed by the DLG or anyother Re-Test Drive 8 Read Sector Failure A Read command during the test has failed.

Western Digital Error Codes

Computers with S.M.A.R.T. Contact System Vendor 221 Test Not Supported Certain older drives do not support certain SMART Self Tests. Replace Drive 207 SMART status failed before the media scan.

Explorer would freeze... Re-test Drive with appropriate diagnostic utility 202 Drive Not Supported Older Western Digital drives are not supported by the diagnostic utility version being used. There could be media errors present on this drive. Re-Test Drive 111 DIAG COMMAND ERROR The drive did not properly respond to test commands.

Check cabling and retest. Western Digital Error Code 0007 ECC is a hardware correction technique that corrects errors. The drive has not responded in the time allotted. https://hardforum.com/threads/wd-diagnostics-error-code-223.1300005/ Replace Drive 210 Self Test Incomplete SMART Self Test failed to complete (e.g. -- timed out).

Suspend Offline collection upon new command. At least ten ECC errors have been detected. What's this I hear about First Edition Unix being restored? Ten or more instances of information on data positioning and location could not be found.

Western Digital Error Code 0007

This may be an anomaly. https://community.wd.com/t/wd20ears-00s8b1-strange-smart-behavior/14205 Retest the drive. Western Digital Error Codes Track 0 also holds information about the drive. Every since then my computer...

Retest after checking the connections. check over here An error has been detected. Check cabling and retest. Drive should be replaced.

After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 46 00 00 00 40 Device Fault; Error: ABRT There may be repairable media errors on a platter. This is a monitoring system, which stores all errors, retries, and power on hours. http://txtbl.com/error-code/wd-error-code-0223.html Version 4.12 for older drives and version 5.00 for current drives.

Ran the WD Data Lifeguard (DLG) from Ultimate Boot CD v5.0.2 and found nothing on Quick test, but found something on Extended test, repaired it and gave error code of 0223. Replace Drive 227 SMART Not Supported Self-Monitoring, Analysis, and Reporting Technology (SMART) Certain older drives do not support SMART. Re-Test Drive 10 Set File Pointer Error A SetFilePointer command during the test has failed.

There were media errors that were within the repair capabilities of diagnostic utility.

I would like to test it before use. I decided to perform a extended test. Drive should be replaced. Hard drive failing?Hey there guys, about six months ago I started receiving an error every few days on my computer on boot, and it was something along the lines of: 'pxe-rom:

This may be due to a media error. Has anyone experienced this before? SCT Feature Control supported. weblink Replace Drive If an error code is encountered that is not in the list above, please Contact Us for additional troubleshooting.

I just figure loading from the image will take about half an hour, and all my configurations and stuff will be already there, where if I install from scratch I'll have Check connections and retest. This may be an anomaly or a defect with the drive. Retest after checking the connections.

I installed the latest official 260.89 drivers and selected clean install. An interrupt command to perform a specific task failed to complete. Check your connections and replace the cable. hard-drive hardware-failure smart share|improve this question edited Apr 23 at 17:44 fixer1234 11.2k122950 asked Nov 22 '13 at 9:09 Antonio 4491718 Can you please post SMART's output?

Replace the drive if the error repeats. If the error repeats, replace the drive. It may also happen when the wrong version of diagnostic utility is used. This error may also appear if the floppy has been infected by a hidden virus.

Replace Drive 3 SMART Attribute Read Failure Self-Monitoring, Analysis, and Reporting Technology (SMART) attribute read failure. Re-test Drive 150 UNKNOWN ERROR An unknown error has occurred during testing. I did put in for a new hard drive and they will be sending me one. It is also possible to see this error on defective Western Digital drives.

The drive should now be defect free. Any further tests I could run? 2)If I am to get a new system drive, what should I get? Stay logged in Search titles only Posted by Member: Separate names with a comma. Replace the drive if the repair fails.

ViVard and GSmartControl for Quick/Extended/Conveyance tests came out clean and error-free.