Home > Error Code > Wd Error Code 0223

Wd Error Code 0223

Contents

Replace Drive 200 Drive Not Tested Supported WD drives are initialized with this status. You may need to rescan to ensure that the repairs were effective. Replace Drive 218 10+ SERVO Errors SERVO 10+. Replace Drive 214 10+ DAM Errors Data Address Mark (DAM) 10+. navigate here

Replace the drive if the error repeats. not all smart errors are created equal, but growth in bad blocks tends to approach exponential over time. Just before you install the new drive I would do another full backup and then clone the disk so you don't have to reload everything. Please contact the system vendor for the above-mentioned information. https://support.wdc.com/knowledgebase/answer.aspx?ID=11711

Western Digital Error Codes

You may also want to reroute your IDE cable away from sources of electronic bus noise such as your CPU, Power Supply, etc. So I ran Western Digital diagnostic as well. Replace the drive. Rate Changes 12/1/16 [OptimumOnline] by dm145400.

According to to western digital's site: 223 Errors Repaired Errors found, but have been repaired successfully. share|improve this answer answered Nov 22 '13 at 9:51 MariusMatutiae 29.6k93361 I have just added SMART status and it shows that Offline_Uncorrectable is zero. An error was reported by the drive during the Write command (to cause the auto-relocation) or the Read Verify command (to verify the relocation happened). Jim WIN7 Ultimate SP1 64bit, IE 11, NTFS, cable, MS Security Essentials, Windows 7 firewall Reply With Quote April 15th, 2010,02:56 PM #2 Midknyte View Profile View Forum Posts StArK RaVinG

The drive is defect free. Western Digital Error Code 0007 It is also possible to see this error on defective Western Digital drives. johnb35, Sep 1, 2015 #4 Okedokey Well-Known Member Messages: 9,189 Also ensure you have the latest chipset drivers particularly if you use a RAID. https://hardforum.com/threads/wd-diagnostics-error-code-223.1300005/ SCT Feature Control supported.

SMART is self monitoring by the hard drive. WDC Support Downloads Knowledge Base Product Registration Warranty Services Contact Ask a Question Contact Support Feedback Other Sites MyCloud.com Online Learning Center CONNECT WD Blog © 2016 Western Digital Technologies, Inc. This may be due to a media or read/write error. Please contact the system vendor for the above-mentioned information.

Western Digital Error Code 0007

No way. Retest after checking the connections. Western Digital Error Codes Replace the drive. Re-test Drive 150 UNKNOWN ERROR An unknown error has occurred during testing.

Re-Test Drive 4 Open Drive Failure Cannot communicate with drive. check over here A clicking noise can indicate that this error has occurred. Replace Drive 557 SERVO 2-9 SERVO is data on track location. Replace Drive 216 10+ IDNF Errors Identified Data Not Found (IDNF) 10+.

Thanks! Why was Vader surprised that Obi-Wan's body disappeared? EDIT2: Different drive worked, but had bootup problems. :X Last edited: Nov 10, 2010 Cerulean, Nov 10, 2010 Cerulean, Nov 10, 2010 #2 Nov 10, 2010 #3 drescherjm [H]ardForum Junkie http://txtbl.com/error-code/wd-hdd-error-code-0223.html Retest.

I installed and tried to run the DLG program using Quick Test. P.S. Replace Drive 227 SMART Not Supported Self-Monitoring, Analysis, and Reporting Technology (SMART) Certain older drives do not support SMART.

Huge cost to add wife to health insurance? [OpenForum] by bumbatafata232.

This error may also be related to memory issues. Replace Drive 211 2-9 Uncorr ECC Errors Error Correction Code (ECC) 2 through 9. This is the pretest initialization code which indicates a drive is ready to be tested, but has not yet been tested. Re-test Drive 134 Busy Timeout Timeout from checking busy bit.

Retest after checking the connections. Replace drive if unable to correct error 118 DAM Error Data Address Mark (DAM) Error. This may be an anomaly or a defect with the drive. weblink Retest after checking the connections.

Re-test Drive with appropriate diagnostic utility 205 Aborted By User Test was aborted by the user (Alt-X pressed during a test). This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection. In any case, even if the failure does not occur in a critical sector, it will entail data loss of some sort. At least ten errors have been detected.

This may be an anomaly. The time now is 04:19 AM. Retest. Retest.