What happens with NowSMS? IMSI not known). Other errors might me permanent or temporary but there is no way to be certain. Basically, when talking directly to a COM port, it means "access denied". http://www.ozekisms.com/index.php?ow_page_number=380
This one worked fine for a couple hours, but it began failing to deliver sms messages over the network... Has anyone had this same problem on any wavecom-based gsm modem? Developed by GXPMEDIA.COM Products NowSMS & MMS Gateway NowSMS MMSC NowWAP Gateway NowSMS Lite About Newsletter What is NowSMS? MonitorTools.com Internet resource for ICT administrators and operators.
If the USB Comport has crashed sometimes the only way to bring it up would be to either physically unplug/plug it back or reboot the server (to do so remotely, issue Bryce Norwood - NowSMS Support Board AdministratorUsername: BrycePost Number: 4539Registered: 10-2002Posted on Wednesday, May 18, 2005 - 07:36 pm: There's another forum participant out (Ashot S), who has mentioned that Wavecom Based upon this, I would agree with Ashot's assessment. http://support.nowsms.com/discus/messages/1/9717.html When the error starts with "+CME ERROR", it means that the error is a device specific error code.
CMS ERROR 69 "Requested facility not implemented" This cause indicates that the network is unable to provide the requested short message service. Gsm Error Codes CMS ERROR 8 "Operator determined barring" This cause indicates that the MS has tried to send a mobile originating short message when the MS's network operator or service provider has forbidden I have read in posts that this makes a difference, though I have no idea how such a remote connection could affect the operation of a serial device attached to the The following table lists the most common error codes.
There are a lot of other possible errors, I have put a list below but these are not even all the possible error messages. *Errors generated by Diafaan SMS Server Invalid https://www.diafaan.com/support-forum/installation-and-setup/error-list-and-recommended-modem/ IMSI or directory number is not allocated to a subscriber). +cme Error 100 For instance, you are trying to read a phonebook entry before entering a pincode. Sms Error Code 69 Please try the request again.
Please try the request again. http://txtbl.com/error-code/webpage-error-codes.html By the way, I am using Remote Desktop to connect to the server all the time. The system returned: (22) Invalid argument The remote host or network may be down. One of the reasons for this is that the error reporting of 3G/GSM modems is not very well defined, the same error message might be used for different causes without much Cme Error 50
WindowsManagement.com Internet Resource for Windows management software. CMS ERROR 17 "Network failure". CMS ERROR 41 "Temporary failure" This cause indicates that the network is not functioning correctly and that the condition is not likely to last a long period of time; e.g., the his comment is here They have been quite sensitive to the new IMEI prefixes in the past.
Generated Tue, 01 Nov 2016 08:08:15 GMT by s_mf18 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.7/ Connection Error Code 44 In Uninor CMS ERROR 28 "Unidentified subscriber" This cause indicates that the subscriber is not registered in the PLMN (i.e. WindowsDevelopment.com Internet Resource for Windows development software.
I believe the USB modem driver is buggy, and it looks like an unrecoverable error. In NowSMS, add a commandpreinitY=at+cmgd=1,4 - "receive SMS messages" for the modem must always be checked, whether you need the received messages or not. I am using Remote Desktop to connect to the server all the time. Cms Error Codes Unfortunately, the error codes that the mobile network or GSM modems generate are not always entirely unambiguous.
The LED on the modem which normally blinks, stays ON all the time. It looks like a crappy USB COM port driver, which is very common. CMS ERROR 128 Telematic interworking not supported x CMS ERROR 129 Short message Type 0 not supported x x CMS ERROR 130 Cannot replace short message x x CMS ERROR 143 weblink and try Ashot's suggestions about CommandPreInit settings. (In case you're not familiar with them, manually edit SMSGW.INI, and under the [Modem - ] section header for your modem, add CommandPreInit0=AT..., then
manufacturer specific Dig deeper! CMS ERROR 96 "Invalid mandatory information" This cause indicates that the equipment sending this cause has received a message where a mandatory information element is missing and/or has a content error Yes, the modem responds to at commands at that time, but it is not registered in the network. Could you help us find what's going on?
Could it be the cause? It can be used for: Phone calls from SQL Phone calls from HTTP Voice and SMS applications Callcenter developers If you are working on telephone solutions, please check out the Ozeki Bryce Norwood - NowSMS Support Board AdministratorUsername: BrycePost Number: 4584Registered: 10-2002Posted on Wednesday, May 25, 2005 - 07:16 pm: This "Error 5" is a new one to me, at least in CMS ERROR 99 "Information element non existent or not implemented" This cause indicates that the equipment sending this cause has received a message which includes information elements not recognized because the
If the modem's SIM card and memory are full of incoming messages it would always act up, whether it's a Wavecom or any other GSM modem. - make sure that the Introduction The error codes listed in this table are called CMS ERROR codes. CMS ERROR 22 "Congestion". Don't try to update it with any version which you are not 100% sure is made for your particular unit, or you would damage it.
Any help is greately appreciated. CMS ERROR 30 "Unknown subscriber" This cause indicates that the subscriber is not registered in the HLR (i.e. The syntax of this extended error is either "+CMS ERROR: xxx" or "+CME ERROR: xxx". It terminates some processes that make the modem freeze. - contact your distributor for a latest Wavecom firmware update.